Call For A Free Estimate!
Read our customer testimonials
SAN LEANDRO - 510.483.9700    HAYWARD - 510.489.6881
OAKLAND - 510.483.9708            SAN JOSE - 408.254.3667
EMAIL NOW

Rolling Doors

R & S is a leading manufacturer of rolling service doors, counter doors, and aluminum grilles. Our doors are manufactured to meet the need for secure, effective, space saving closures that are endurance tested while providing outstanding economy and value. A variety of mountings, operation methods, materials, and finish options are available. Contact us today to have a free on site evaluation of your service doors.

 

 

 

Product variations provide solutions for specific requirements such as:

  • Weather and Temperature Control
  • Ventilation and Visibility
  • Access and Egress
  • Fire Protection and Smoke Control >> Click Here To View Our Fire Rated Doors
  • Manual or Motorized

 

Custom engineering capabilities allow many standard R & S rolling door products to be adapted for special uses including:

  • Combination Door and Grilles (for ventilation and visibility)
  • Crane Doors (for T-shaped openings)
  • Aircraft Hanger Tail-Section Doors
  • Cabinet Enclosures (with curved or inclined guides)
  • Horizontal Covers (over openings in floors or ceilings)

 



Rolling Service Doors

 


Standard Features:

  • 6" minimum diameter structural steel pipe barrel
  • Oil tempered torsion springs on continuous cold-rolled steel shaft
  • Steel plate brackets attach to wall angles
  • Interior or exterior, face of wall or between jamb mount
  • Prime-painted galvanized steel hood
  • Chain operation with cast iron gears
  • Interlocking prime-painted galvanized steel slats
  • Formed steel channel or structural steel angle guides and continuous wall angle mounting
  • Extruded aluminum or double steel angle foot piece with astragal


Slat Options:


**Note: All items featured may be optional on above door lines and can be changed without notice.

 

Other Options:

  • Climate-Guard Weather Stripping: Climate control is provided by the combination of a flat slat curtain, hood-baffle, guide weather stripping and astragal.
  • Thermal-Guard Insulation: An effective thermal barrier is created by the combination of 22 gage (min.) steel flat-faced slats, 3/4" polyurethane foam, and 24 gage steel back slats.
  • Increased Windload Capacity: Curtain designs to withstand windloads exceeding 20psf.
  • High Cycle Construction: Designs to provide up to 150,000 operating cycles for high use areas.
  • Perforated Slats: 3/64" diameter holes on 5/64" staggered centers in type 25 slats provide 30% open area for ventilation and visibility through the curtain.
  • Intermediate Grill: Partial grille curtain connecting type 30 slats above and below for ventilation and visibility.
  • Sloped or Stepped Footpiece: For special sill conditions.
  • Cylinder Locks: On foot piece or guide for extra security.
  • Pass Door: 3'-0"x6'-8" hollow metal door in a steel frame for access through the curtain when closed; Frame is hinged to guide and swings clear to allow use of entire door opening when curtain is raised; handicap option, custom sizes, windows and special hardware available.
  • Galvanized Finish: On foot piece, guides, brackets and barrel.
  • Powdercoat Finish: On curtain, foot piece and guides.



Aluminum Grille Gates

 


Standard Features:

  • 6" Minimum diameter structural steel pipe barrel
  • Optional aluminum or galvanized steel hood
  • Oil tempered torsion spring on continuous cold-rolled steel shaft
  • Aluminum grille curtain (see patterns below)
  • Extruded aluminum guides & continuous steel wall angles
  • Steel plate brackets attached to wall angles
  • Extruded aluminum tubular bottom bar


Standard Grille:

Constructed in the standard straight link pattern for grilles in normal usage such as shopping malls and storefronts. The all aluminum curtain is formed of horizontal rows of 5/16" aluminum rods spaced 1 1/2" apart to be connected by vertical 3/4" aluminum links spaced 9" apart.

 



Heavy Grille:

Constructed in the heavy straight link pattern for grilles in high usage applications such as parking garages. Curtain is formed of horizontal rows of 5/16" aluminum rods alternating with 1/4" galvanized steel rods covered with a 5/16" aluminum tube sleeve. Rods are spaced 1 1/2" apart and connected by vertical 3/4" aluminum links spaced 9" apart. A brick pattern is available.

 



Other Options:

  • High Cycle Construction: Designs to provide up to 150,000 operating cycles.
  • Emergency Egress System: Recessed pull handle in a flush mount enclosure mechanically disconnects motor operator to provide partial opening of grille for emergency exit.
  • Support Tubes: Square steel tubes attached to floor and structure above to provide mounting for grille.
  • Sloped Foot Piece: For special sill conditions.
  • Soffit Flange Cover: 5 1/2" wide flange on bottom of footpiece to conceal slot required for above ceiling installations.
  • Cylinder Locks: On foot piece.
  • Hood: Formed from galvanized steel or aluminum sheet
  • Fixed Grille Panel: Grille curtain in a supporting frame.
  • Anodized Finish: Clear, dark bronze, gold, black and other color anodized finishes on curtain, foot piece, guides and hood.

 



Counter Doors

 


Steel and Stainless Steel:

Strength and durability of a rolling service door with compact design and clean appearance. Although primarily used as a closure on counter openings, it may also be used on openings providing walk-thru or drive-thru access. Counter door construction can be modified to provide for stainless steel service doors up to 16' wide, 10' high and 144 square feet.

 

  • Slat Type - Interlocking type 18 flat galvanized steel or stainless steel slat options
  • Barrel - Steel pipe houses spring assembly and supports curtain with maximum deflection of .03 inch per foot of width
  • Springs - Torsion springs on continuous cold-rolled steel shaft
  • Brackets - Steel plate brackets attach to guides to support curtain and barrel
  • Guides - Box shape guides formed from steel or stainless steel
  • Foot Piece - Single angle or tubular foot piece with astragal
  • Hood - 24 gage galvanized or stainless steel hood reinforced with top and bottom flanges to limit deflection
  • Locking Mechanism - Slide bolt locks on single angle foot piece and cylinder lock on optional tubular foot piece
  • Finish - Galvanized steel slats and hoods are pre-finished with a baked on grey polyester primer before forming. Steel foot piece, guides and brackets receive one coat of rust inhibiting grey primer. Exposed stainless steel provided with #4 finish.
  • Operation - Push-up to 14' wide and awning crank on larger sizes is standard (awning crank should be considered when doors are to be operated over a deep counter over 7' high). Optional chain hoist or motor operator.


Aluminum:

Offers a compact design and attractive appearance. Anodized extruded aluminum components combine lightweight with a smooth and bright finish and excellent corrosion resistance for a variety of applications. Counter door construction can be modified to provide for anodized aluminum service doors up to 12' wide, 10' high and 100 square feet.

  • Slat Type - Interlocking type 15 flat slats are extruded from 6063 alloy aluminum
  • Barrel - Steel pipe houses spring assembly and supports curtain with maximum deflection of .03 inch per foot of width
  • Springs - Torsion springs on continuous cold-rolled steel shaft
  • Brackets - Steel plate brackets attach to guides to support curtain and barrel
  • Guides - Extruded aluminum guides are bolted to aluminum wall angles and fitted with nylon pile wear strips
  • Foot Piece - Extruded aluminum tubular foot piece with astragal
  • Hood - Formed from aluminum sheet and reinforced with top and bottom flanges to limit deflection
  • Locking Mechanism - Slide bolt locks and optional cylinder lock
  • Aluminum slats, foot piece, guides and hood are clear anodized. Steel brackets receive one coat of rust inhibiting grey primer. Dark bronze and other color anodized finishes are optional.
  • Operation - Push-up is standard and awning crank on larger sizes is standard (awning crank should be considered when doors are to be operated over a deep counter over 7' high). Optional chain hoist or motor operator.

 


Speak with one of our customer
service representative. Type Here.

    • Garage Doors
    • Garage Door Openers
    • Commercial Doors
    • Gates
    • Repair Work

R & S Headquarters

R&S Overhead Garage Door, Inc.
San Leandro, CA
(510) 483-9700 Phone
(510) 483-2058 Fax
SERVING
San Leandro, Castro Valley, Oakland, Alameda,
Piedmont & San Lorenzo

R&S Erection of South Alameda County, Inc. | Hayward, CA
(510) 489-6881 Phone
(510) 489-2861 Fax
SERVING
Hayward, Union City,
Newark, Fremont,
San Jose, Santa Clara,
Milpitas & Palo Alo